Level Check Code: Difference between revisions
From Mike Beane's Blog
(Created page with "<code> ; 9 Point Level Check - RB G90 ; POSITION 1 G1 Z4 G1 X32 Y36 G1 Z0 M0 ; POSITION 2 G1 Z4 G1 X32 Y206 G1 Z0 M0 ; POSITION 3 G1 Z4 G1 X202 Y206 G1 Z0 M0 ; POSITION 4...") |
m (→Code) |
||
| (11 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
< | [[File:9PointLevelTest.png|thumb|Plot path|right]] | ||
==Desc== | |||
Performs a 9 point check on bed leveling. | |||
Save as .gcode for printer and run. | |||
==Notes== | |||
* I have POS 1-5 saved as separate files on the SD card under POS\ for quick reference, as well as this master file for a full check. | |||
* Used on an Ender 3 | |||
* I perform the test on a cold bed, if you are looking for a hot test, this is not for you | |||
** Gap checking with index card (5 prints since testing with index card, all good. Prior paper yielded spaghetti). | |||
** Cold bed, no expansion (! or ?) | |||
** As always: YMMV | |||
<hr> | |||
==Code== | |||
<pre> | |||
; 9 Point Level Check - RB | ; 9 Point Level Check - RB | ||
G28 ; Go to origin on all axis | |||
G90 | G90 | ||
| Line 42: | Line 64: | ||
; POSITION 7 | ; POSITION 7 | ||
G1 Z4 | G1 Z4 | ||
G1 | G1 X117 Y206 | ||
G1 Z0 | G1 Z0 | ||
M0 | M0 | ||
| Line 48: | Line 70: | ||
; POSITION 8 | ; POSITION 8 | ||
G1 Z4 | G1 Z4 | ||
G1 | G1 X202 Y121 | ||
G1 Z0 | G1 Z0 | ||
M0 | M0 | ||
| Line 54: | Line 76: | ||
; POSITION 9 | ; POSITION 9 | ||
G1 Z4 | G1 Z4 | ||
G1 | G1 X117 Y36 | ||
G1 Z0 | G1 Z0 | ||
M0 | M0 | ||
G28 ; Go to origin on all axes | |||
; Home | ; Home | ||
| Line 65: | Line 89: | ||
; Disable Motors | ; Disable Motors | ||
M84 | M84 | ||
</ | |||
</pre> | |||
[[Category:3D Printing]] | [[Category:3D Printing]] | ||
Latest revision as of 14:27, 12 December 2021
Desc
Performs a 9 point check on bed leveling.
Save as .gcode for printer and run.
Notes
- I have POS 1-5 saved as separate files on the SD card under POS\ for quick reference, as well as this master file for a full check.
- Used on an Ender 3
- I perform the test on a cold bed, if you are looking for a hot test, this is not for you
- Gap checking with index card (5 prints since testing with index card, all good. Prior paper yielded spaghetti).
- Cold bed, no expansion (! or ?)
- As always: YMMV
Code
; 9 Point Level Check - RB G28 ; Go to origin on all axis G90 ; POSITION 1 G1 Z4 G1 X32 Y36 G1 Z0 M0 ; POSITION 2 G1 Z4 G1 X32 Y206 G1 Z0 M0 ; POSITION 3 G1 Z4 G1 X202 Y206 G1 Z0 M0 ; POSITION 4 G1 Z4 G1 X202 Y36 G1 Z0 M0 ; POSITION 5 G1 Z4 G1 X117 Y121 G1 Z0 M0 ; POSITION 6 G1 Z4 G1 X32 Y121 G1 Z0 M0 ; POSITION 7 G1 Z4 G1 X117 Y206 G1 Z0 M0 ; POSITION 8 G1 Z4 G1 X202 Y121 G1 Z0 M0 ; POSITION 9 G1 Z4 G1 X117 Y36 G1 Z0 M0 G28 ; Go to origin on all axes ; Home G1 Z4 G1 X0 Y0 G1 Z0 ; Disable Motors M84