Distant Screws II Challenge Coin: Difference between revisions
From Mike Beane's Blog
m (→Painting) |
m (→Directions) |
||
| Line 40: | Line 40: | ||
==Directions== | ==Directions== | ||
===Printing=== | ===3D Printing=== | ||
<youtube>ZYjBJZRjBho</youtube> | <youtube>ZYjBJZRjBho</youtube> | ||
| Line 65: | Line 65: | ||
<hr> | <hr> | ||
====Blue Highlights==== | ====Blue Highlights==== | ||
[[File:03 LSN BlueHighlights.jpg]] | [[File:03 LSN BlueHighlights.jpg|thumb]] | ||
* Lightly apply blue acrylic paint to various raised areas. I used a toothpick to do the coins. There are one or two green coins in the bunch, however blue seemed to be the best choice. | * Lightly apply blue acrylic paint to various raised areas. I used a toothpick to do the coins. There are one or two green coins in the bunch, however blue seemed to be the best choice. | ||
====Silver Dusting==== | ====Silver Dusting==== | ||
[[File:04_LSN_DustedWithSilver.jpg]] | [[File:04_LSN_DustedWithSilver.jpg|thumb]] | ||
* Lightly apply a dusting of silver. The goal is to try and let some of the gloss black poke through. Your call on the final outcome. In my batch, the 13 coins ran a range between almost full silver vs a moderate dusting. | * Lightly apply a dusting of silver. The goal is to try and let some of the gloss black poke through. Your call on the final outcome. In my batch, the 13 coins ran a range between almost full silver vs a moderate dusting. | ||
Revision as of 14:24, 27 March 2021
About
- Evelyn's Story
- JelloWiggler's Frontier Forums Thread
- Expedition Page on EDSM
- Evelyn's Light Position on EDSM
ReadMe
A how-to for printing the 3D LS DS II Challenge Coin for anyone that was on the 2021 Distant Screws II Expedition.
The front-side features the classic LS Logo, the expedition name, dates and the waypoint distances traveled.
The backside features the four points of the journey (ROSS310-EVELYNS LIGHT-COLONIA-QAMA) and a star to honor Evelyn Faye Roy.
Printing Suggestions
Scale to 60mm x 60mm x 8mm (or 10mm)
Super Quality
1) With trees: On an edge - will require sanding and clean up. 2) In halves:
Duplicate the STL on the bed
Sink both below the bed to 1/2 the Z width (-4mm or -5mm)
Flip one of the faces
Print
Glue together
Sand edge as needed with 220g and 500+
Created by RabbiBob 3/1/2021 w/ Blender 2.9.x
Download
- Download: Zip file 4.5MB
Directions
3D Printing
Sanding
- Lightly sand the edges and any surface you can without damaging the raised items. You can see in some of the final coins the ones where a combination of sanding and primer worked well and others that didn't during testing.
Painting
- Someday I'll buy an airbrush kit. Until then, fun with aerosol cans!
- Requirements:
- Krylon Sandable Primer
- Gloss Black spray paint
- Blue acrylic paint
- Metallic Silver spray paint
- Something to fit under the coin to keep if off the resting surface (washer, nut, etc)
Primer
- Do two separate coats of prime where the first coat is close to a dusting.
- Second coat should fill in a lot of the printer lines
Black Coat
- Apply a single shiny black coat
Blue Highlights
- Lightly apply blue acrylic paint to various raised areas. I used a toothpick to do the coins. There are one or two green coins in the bunch, however blue seemed to be the best choice.
Silver Dusting
- Lightly apply a dusting of silver. The goal is to try and let some of the gloss black poke through. Your call on the final outcome. In my batch, the 13 coins ran a range between almost full silver vs a moderate dusting.
Visting
