Distant Screws II Challenge Coin: Difference between revisions
From Mike Beane's Blog
m (→ReadMe) |
m (→Painting) |
||
| Line 57: | Line 57: | ||
** Blue acrylic paint | ** Blue acrylic paint | ||
** Metallic Silver spray paint | ** Metallic Silver spray paint | ||
** Mod Podge® Clear Acrylic Sealer, Matte | |||
** Modelling glue | |||
** Something to fit under the coin to keep if off the resting surface (washer, nut, etc) | ** Something to fit under the coin to keep if off the resting surface (washer, nut, etc) | ||
<hr> | <hr> | ||
| Line 75: | Line 77: | ||
[[File:04_LSN_DustedWithSilver.jpg|thumb]] | [[File:04_LSN_DustedWithSilver.jpg|thumb]] | ||
* Lightly apply a dusting of silver. The goal is to try and let some of the gloss black poke through. Your call on the final outcome. In my batch, the 13 coins ran a range between almost full silver vs a moderate dusting. | * Lightly apply a dusting of silver. The goal is to try and let some of the gloss black poke through. Your call on the final outcome. In my batch, the 13 coins ran a range between almost full silver vs a moderate dusting. | ||
====Glue==== | |||
* Glue the halves together | |||
* Only four or five dabs of model glue is needed. Don't let it ooze from the middle onto the edges of the coin. | |||
====Seal==== | |||
* Seal the coin with Mod Podge Clear Acrylic Sealer | |||
* This helps not only protect the coin but also to seal in some of the paint smell | |||
==Visting== | ==Visting== | ||
Revision as of 14:32, 27 March 2021
About
- Evelyn's Story
- JelloWiggler's Frontier Forums Thread
- Expedition Page on EDSM
- Evelyn's Light Position on EDSM
ReadMe
A how-to for printing the 3D LS DS II Challenge Coin for anyone that was on the 2021 Distant Screws II Expedition.
The front-side features the classic LS Logo, the expedition name, dates and the waypoint distances traveled.
The backside features the four points of the journey (ROSS310-EVELYNS LIGHT-COLONIA-QAMA) and a star to honor Evelyn Faye Roy.
Printing Suggestions
Scale to 60mm x 60mm x 8mm (or 10mm)
Super Quality
- With trees: On an edge - will require sanding and clean up.
- In halves:
- Duplicate the STL on the bed
- Sink both below the bed to 1/2 the Z width (-4mm or -5mm)
- Flip one of the faces
- Sand edge as needed with 220g and 500+
- Prime
- Paint Black Gloss
- Paint Blue acrylic
- Dust paint Silver metallic
- Glue together
Created by RabbiBob 3/1/2021 w/ Blender 2.9.x
Download
- Download: Zip file 4.5MB
Directions
3D Printing
Sanding
- Lightly sand the edges and any surface you can without damaging the raised items. You can see in some of the final coins the ones where a combination of sanding and primer worked well and others that didn't during testing.
Painting
- Someday I'll buy an airbrush kit. Until then, fun with aerosol cans!
- Requirements:
- Krylon Sandable Primer
- Gloss Black spray paint
- Blue acrylic paint
- Metallic Silver spray paint
- Mod Podge® Clear Acrylic Sealer, Matte
- Modelling glue
- Something to fit under the coin to keep if off the resting surface (washer, nut, etc)
Primer
- Do two separate coats of prime where the first coat is close to a dusting.
- Second coat should fill in a lot of the printer lines
Black Coat
- Apply a single shiny black coat
Blue Highlights
- Lightly apply blue acrylic paint to various raised areas. I used a toothpick to do the coins. There are one or two green coins in the bunch, however blue seemed to be the best choice.
Silver Dusting
- Lightly apply a dusting of silver. The goal is to try and let some of the gloss black poke through. Your call on the final outcome. In my batch, the 13 coins ran a range between almost full silver vs a moderate dusting.
Glue
- Glue the halves together
- Only four or five dabs of model glue is needed. Don't let it ooze from the middle onto the edges of the coin.
Seal
- Seal the coin with Mod Podge Clear Acrylic Sealer
- This helps not only protect the coin but also to seal in some of the paint smell
Visting
